24-05-2021

Icom F320 Programming Software

Icom CS-F300 Programming Software for Icom IC-F310 IC-F320 IC-F410 IC-F420. $16.95; Buy It Now. Would like to advise User's of the following regarding this download service for User Manuals and Service Manuals. If you agree to the following, push the AGREE button below to proceed. The following apply to this download service. Icom IC-f320-6 programming help If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post or view threads: click the register link above to proceed.

  1. Free Programming Software

Sub-categories

Icom f320 programming software free
  • Amateur Radio Utilities

    Software Tools and utilities associated with Amateur radio

    (2 entries, 0 subcategories)

  • CAT Control Software

    CAT (Computer Aided Transceiver) software

    (2 entries, 0 subcategories)

  • EchoAddons

    Applications for use in conjunction with Echolink
    Maintained by Peter, EI4JR.

    (24 entries, 0 subcategories)

  • Firmware

    Firmware (ROM images) for radio and radio related products by manufacture.

    (29 entries, 8 subcategories)

  • Ham Radio Deluxe Addons

    Addons for Ham Radio Deluxe (HRD).
    Maintained by Peter, EI4JR.

    (1 entry, 0 subcategories)

  • Manuals

    Service Manuals & Schematics

    A vast collection of Service Manuals, User Manuals, Schematic Diagra…

    (207 entries, 47 subcategories)

  • Military Radio

    (11 entries, 4 subcategories)

  • Radio & Electronics e-Books

    Information and data related to the Radio & Electronics world including Amateur Radio publications.

    (11 entries, 0 subcategories)

  • Radio Programming Hardware

    Interfaces, RIB boxes, cables etc. for programming.

    (10 entries, 0 subcategories)

  • Radio Programming Software & Data

    Radio programming applications and documentation of interest to Radio Amateurs. This section incl…

    (708 entries, 65 subcategories)

  • Tritan

    (0 entries, 0 subcategories)

  • Utilities

    Useful tools to assist the radio programmer

    (20 entries, 0 subcategories)

#32928 (In Topic #25183)
Hello
Newb here. Nice site
I am looking specifically for how to make a USB programming cable. It surely can't be hard to do as what I can find it is only two wires. But I don't want that magic smoke to come out either.
And maybe a direction to where to find the software would be nice too.
One last question. Will chirp work?
de Kb5lbo
Rich
cable#http://www.ebay.com/itm/USB-Programming-Cable-for-ICOM-IC-F320-IC-F221-OPC-592-/250879704438?hash=item3a69987d76:g:8REAAOxyjP1RzvaY (http://www.ebay.com/itm/USB-Programming-Cable-for-ICOM-IC-F320-IC-F221-OPC-592-/250879704438?hash=item3a69987d76:g:8REAAOxyjP1RzvaY)
and another one#http://www.409shop.com/409shop_product.php?id=103010 (Cable for ICOM Icom IC-F220 IC-F320 F420 OPC-592 409shop walkie talkie- Radio)
and chirp wont work.you need dos on you computer to run this software.i can upload the software for ok.
i dont have the wiring but her is cable if you want to purchase ok
If it is a DOS program can't be too big. Soooo can you email it to me? Rfnut2001 at yahoo dot com please?
Thank you!
I still want to try making a cable before I go purchase one.
you need the Icom CS-F300 programming software,
I dont see it in the downloads, it is listed in the Back Catalogue.
the cable is a OPC-592
if you buy a usb cable make sure it has the FTDI chip.
to build one you need to start with a CP2102 usb to TTL or FTDI friend and a 1n4148 diode, fairly simple to wire it up.
you can buy a cable about as cheap as the usb to ttl.
again if buying a usb cable make sure it is FTDI not prolific.
Saludos amigo ya subi el programa que necesita unsted debe generar un tike para poder bajarlo
the cs-f300 I have is a dos program.
I did open the program in windows XP and it ran.
but that dont mean it will work properly.
if it does using a usb cable may be possible.
Building a cable would be great You can do it for 20$ or less and then make it more universal for other types of radios at the same time. Mouser or Digikey will have the FTDI USB cable with dupont connectors on on end you go from there to adapt to particular radios.
Good Luck
Tim
if you have serial port dont use usb cable.serial is better.less headache all if is anyone of the above FTDI or prolific. which you can buy if you going to buy any.i hate to see the member has issue and the problem continue

tech said

if you have serial port dont use usb cable.serial is better.less headache all if is anyone of the above FTDI or prolific. which you can buy if you going to buy any.i hate to see the member has issue and the problem continue

Agree 100% Max 232 to ttl chips the best way to go
F320thats all I use here for program cables.
i only use serial .except three of them which is usb .two of them which i made and one i purchased the only reason i use them is because they dont make them serial.so i cant do anything about that.
I also agree a serial is best
my main programming interface is serial using a MAX 232 as of now it supports Icom OPC 1122, OPC 478 and Vertex Standard CT-42.
when I need different cable all I have to do is make adaptors.
instead of using a 1n4148 diode I used a 7407 ic.
I also made it so it can be powered by USB, 9 volt battery or power supply.
I have 1 USB cable for kenwwood and Relm and some Chinese HT's it is a prolific clone.

Last edit: by 35rem

Software
Look at this links … Make sure it helps you. I have the Software too. hug
http://i.imgur.com/9KXYtMd.png (http://i.imgur.com/9KXYtMd.png)
http://i.imgur.com/36fP7P0.png (http://i.imgur.com/36fP7P0.png)

Last edit: by MASTERMAG

Rfnut2001 asked about making a usb cable not a serial.
most computers now are usb only, not everyone can have and keep up older computer with a serial port.
also some newer radios use a usb cable and have there own drivers, some even can be accessed over wireless network.
the software has been uploaded here and Awaiting Validation
just little advice you can get the dell 610 and dell 620 on ebay .these 2 have serial port and usb.very cheap .i got one in very good condition for 20.00 us.check it out you will be surprised.
I have an icom OPC-1122u now. Wondering if anyone has tried it. Someone listed the software I need, but can't find it. Also if anyone knows a pin out for the mic on this rig. I have a yeasu mh-25abj mic I want to use on it..
Any assistance would be greatly appreciated!

Free Programming Software

OPC1122 wont work you need the OPC-592
need to ask for the software to be validated
https://hamfiles.co.uk/index.php?page=2bvalidated
Radio Programming Software & Data/Icom Programming Software/Icom CS-F300 uploaded by N4FV